The EM78F664N is an 8-bit microprocessor designed and developed with low-power, high-speed CMOS technology and high noise immunity. It has an on-chip 4Kx13-bit Electrical Flash Memory and 256x8-bit in system programmable EEPROM. It provides three protection bits to prevent intrusion of user's Flash memory code. Twelve Code option bits are also available to meet user's requirements.
With its enhanced Flash-ROM feature, the EM78F664N provides a convenient way of developing and verifying user's programs. Moreover, this Flash-ROM device offers the advantages of easy and effective program updates, using development and programming tools. User can avail of the ELAN Writer to easily program his development code.
- 4K×13 bits on-chip Flash memory
- 144×8 bits on-chip registers (SRAM)
- 256 bytes in-system programmable EEPROM
*Endurance: 1,000,000 write/erase cycles
- More than 10 years data retention
- 8-level stacks for subroutine nesting
- 3 programmable Level Voltage Reset LVR : 4.1V, 3.7V, 2.7V
- Less than 1.5 mA at 5V / 4 MHz
- Typically 20 μA, at 3V / 32kHz
- Typically 1.5 μA, during sleep mode
- 4 bidirectional I/O ports: P5, P6, P7 and P8
- 25 I/O pins
- Wake-up port : P6
- High sink port : P6
- 14 programmable pull-high I/O pins
- 14 programmable pull-down I/O pins
- 8 programmable open-drain I/O pins
- External interrupt with Wake-up : P60
- 2.5V~5.5V at -40°C~85°C (Industrial)
- 2.3V~5.5V at 0°C~70°C (Commercial)
- Operating frequency range (base on two clocks)
- Crystal mode : DC~16MHz @ 5V~5.5V ; DC~8MHz @ 3V~5.5V ; DC~4MHz @ 2.3V~5.5V
- ERC mode : DC~16MHz @ 5V~5.5V ; DC~8MHz@ 3V~5.5V ; DC~4MHz @ 2.3V~5.5V
- IRC mode : DC~16MHz @ 5V~5.5V ; DC~4MHz@ 2.3V~5.5V
Internal RC
Frequency |
Drift Rate |
Temperature
(-40°C~85°C) |
Voltage
(2.5V~5.5V) |
Process |
Total |
| 4MHz |
± 3% |
± 5% |
± 2.5% |
± 10.5% |
| *16MHz |
± 3% |
± 5% |
± 2.5% |
± 10.5% |
| 8MHz |
± 3% |
± 5% |
± 2.5% |
± 10.5% |
| 455kHz |
± 3% |
± 5% |
± 2.5% |
± 10.5% |
* 16 MHz operating temperature: -40°C ~ 50°C
- Fourteen available interrupts
- Internal interrupt : 11
- External interrupt : 3
- 8 channels Analog-to-Digital Converter with 10-bit resolution
- One set of comparator (offset voltage: smaller than 10 mV)
- Two channels Pulse Width Modulation (PWM ) with 10-bit resolution
- Two 8-bit Timer/Counter
- TC1 : Timer/Counter/Capture
- TC3 : Timer/Counter/PDO (programmable divider output)/PWM (pulse width modulation)
- TC2 : Timer/Counter/Window
- Serial transmitter/receiver interface
- Serial Peripheral Interface (SPI): Three-wire synchronous communication
- Universal Asynchronous Receiver/Transmitter (UART)
- 8-bit real time clock/counter (TCC) with selective signal sources, trigger edges, and overflow interrupt
- External interrupt input pin
- 2/4/8/16 clocks per instruction cycle selected by code option
- Power down (Sleep) mode
- High EFT immunity
- Single instruction cycle commands
- Special Features
- Programmable free running Watchdog Timer
- Power-on voltage detector available (2.0V ~ 2.2V)
- 24-pin skinny DIP 300 mil : EM78F664NK24J/S
- 24-pin SOP 300 mil : EM78F664NSO24J/S
- 28-pin skinny DIP 300 mil : EM78F664NK28J/S
- 28-pin SOP 300 mil : EM78F664NSO28J/S
- 32-pin QFN 5×5 mm : EM78F664NQN32J/S
Note: Green products do not contain hazardous substances. |
